Industries

• sizeΦ90x8mm
• 5000hole xΦ1x8mm
• for semiconductor
• Also available in Hastelloy

• M12x30
• With hexagonal hole

• Long thing200mm
• Outer diameter from φ4

• M6 
• Outer screw

• Small diameter Φ6

• Outer screw

• Tip diameter　φ0.1、φ0.2、φ0.3、φ0.4
• L=20mm
• M4 Screw
• φ0.7 Hole drilling

• Inner screw

• Joint-Cutting taper screw

• Machining

• Machining

• Machining

• Φ0.5Hole drilling
• Pitch 0.5mm　thickness 2mm

・小径深穴加工(Φ0.5×70L)

・計72穴

• Paper thickness is 0.1mm
• Product thickness is 0.05mm

• ハステロイC276でのM0.6ネジ加工
• マイナスドライバー用のすり割り溝0.15mm
• SUS304から更に耐食性の強い金属への要求がありハステロイを提案して製作
• 他にもSUS630での製作実績あり
• 実物は肉眼では点にしか見えません

• Pure M5 Bolt

• Sterling silver　99.99%Ag
• Knurling

• Process all from φ8 with a combined lathe processing machine.
• Penetrate φ1 hole in longitudinal direction.
• Penetrate φ2 hole in transverse direction.
• M5 Outer screw. M4 Inner screw.
• D cut and groove processing.

• Permalloy Ring

• Processing from round bar.
• Wall thickness 0.2~0.8.
• Outer diameter φ4～8.  Full length 10mm.

• M3
• Set screw

• Φ2×L3.5mm  Pin

• Shaft
• Full length 300mm
• End face M5 Tapping

• Wall thickness 0.2
• Outer diameter Φ8.5
• Inner diameter Φ4
• Full length 2.5ｍｍ

• M5x8(L)、M5x12(L) 
• Screw with hexagon hole

• Wall thickness 0.4
• Outer diameter Φ9
• Inner diameter Φ4
• Full length 2mm

• Tungsten processed thinner than paper

• Product size is Φ4.3×4.2mm
• Product thickness is 0.05mm

• 左がPBパーマロイ、右がPCパーマロイ
• Left is PB Permalloy,Right is PC Permalloy.

• Tantalum composite processing

• Inner diameter accuracy ±3microns. Surface roughness Ra0.5.
• Mass production processing.  
• Thousands produced monthly.
• Outer diameter φ12× Inner diameter φ6. Not through.
• M3 tap on the other side.

• Nozzle shape
• Outer diameter 0.2mm, inner diameter 0.15mm, wall thickness 0.025mm
• Penetrating a 1mm hole from the other side

• Spherical procesing and Turning process to make surface roughness uniform

• Φ7

• M2.6　Tapping

• M4 Screw

• width 0.8mm
• Slit processing

• Hard turning of inner diameter and end face after heat treatment.
• Surface roughness Ra0.8

• Brass Products

• Process all from φ36 with a combined lathe processing machine.

• With a combined lathe processing machine.

• Pure Copper
• with  combined lathe processing machine

• M3～M8
• Pure Tungsten Screw on Sale
• inch size available
• inspection by gauge

• Official seal size stamp made with Tungsten
• Made with Aluminum and pure copper for weight comparison

• Bearing processing

• Complete heat treatment

• M2.5　Screw

• with a combined lathe processing machine.

• SUS316
• with a combined lathe processing machine.

• Processing from round bar by combined lathe processing

• Hard turning inner diameter after heat treatment
• Inner diameter φ5×L30mm.
• Tolerance range ±4μ
• Surface roughness Ra0.6

• Lathe cutting＋Machining

• Hard turning after heat treatment.
• Outer diameter is machined on R surface.

• Edison hard processing HRC65
• Lapping after polishing 　Rmax0.3S

• The left, φ0.1  L15mm Cutting

• Inner diameter φ0.8
• Tolerance range 10μ

• Teper processing

• Outer diameter φ32. 
• Hard turning after heat treatment.
• HRC62.
• Angle tolerance ±0.03 degrees.　
• Roundness 5μ. 
• Outer diameter finish is Rz0.8.

• Additional processing of forged products.
• Inner diameter tolerance ±5μ

• Drilled φ0.2 hole in Hastelloy C276 of  L20(aspect ratio 100) and L30(aspect ratio 150).
• Through 0.1mm thread.

• PB Permalloy
• Combined processing

• Process all from φ12 with a combined lathe processing machine.
• Penetrate φ1 hole in longitudinal direction.
• M5 Outer screw. M4 Inner screw.
• D cut and groove processing.

• 42Alloy
• Microfabrication

• Inside diameter Φ6ｘL75mm
• Long through hole

• Block

• Φ6

• Processing from φ32 with a combined lathe processing machine.

• Φ5

• Φ5

• Chopstick pillow

• Processing with a comb-type NC lathe.
• L28mm,18mm,14mm,14mm from left.
• Penetration of  φ0.2mm hole in the middle.

• φ0.5, L24.5貫通

• Φ0.5穴加工

• 薄肉加工　厚み0.062

• Φ0.2穴加工(ﾋﾟｯﾁ0.4mm　厚み2mm)